Position: Home > Circuit Diagram > power supply circuit > Index 17
Low Cost Custom Prototype PCB Manufacturer

power supply circuit

Index 17



Basic UPS Power Supply 3

Published:2013/7/17 21:47:00 Author:muriel | Keyword: Basic, UPS , Power Supply

Basic UPS Power Supply 3
  (View)

View full Circuit Diagram | Comments | Reading(529)

Basic UPS Power Supply 2

Published:2013/7/17 21:47:00 Author:muriel | Keyword: Basic , UPS, Power Supply

Basic UPS Power Supply 2
  (View)

View full Circuit Diagram | Comments | Reading(303)

Basic UPS Power Supply

Published:2013/7/17 21:47:00 Author:muriel | Keyword: Basic, UPS, Power Supply

Basic UPS Power Supply
This circuit is a simple form of the commercial UPS, the circuit provides a constant regulated 5 Volt output and an unregulated 12 Volt supply. In the event of electrical supply line failure the battery takes over, with no spikes on the regulated supply.   (View)

View full Circuit Diagram | Comments | Reading(405)

Voltage Inverter 2

Published:2013/7/17 21:46:00 Author:muriel | Keyword: Voltage Inverter

Voltage Inverter 2
This simple and inexpensive circuit can produce a dual (positive and negative) voltage from a single supply input. It is therefore extremely useful for powering opamp and other circuits that require a dual voltage from a single battery. The circuit will operate at an input voltage from around 5V to 20V and produce a output from +-2.5V to +-10V.   (View)

View full Circuit Diagram | Comments | Reading(403)

Pulse Charger for reviving tired Lead Acid batteries

Published:2013/7/17 21:39:00 Author:muriel | Keyword: Pulse Charger , reviving tired, Lead, Acid batteries

Pulse Charger for reviving tired Lead Acid batteries
If you own a motorcycle, a motor home, a caravan, a lawn mover, a day cruiser or maybe a vintage car you must at some point had to write off a lead acid battery. When a battery is improperly charged or allowed to self-discharge as occurs during non-use, sulphate crystals build up on the battery's plates. The sulphate preventing the battery from being fully charged and therefore it is unable to deliver its full capacity. When trying to charge a battery in this state it only gets hot and looses water, the gravity of the electrolyte is not increasing to its normal “full charge” state. The only thing you do is killing the battery completely. If a battery has a resting voltage of at least 1.8 Volts/cell and no cells are shorted, desulphation of its plates can be done. This circuit is an add-on and part for a modification of a normal charger and it takes care of the sulphate problem. The project: get hold of an old charger, big or small it’s your choice depending on the size of batteries you normally handle (bigger is better). There are some tricks to boost the performance if you need it. Start by ripping out everything except the transformer and the rectifier. Some older chargers are equipped with fin rectifiers, which have high voltage drop and must be replaced. Replace with a rugged bridge rectifier that can cope with the amperes. All wiring on secondary should be short and heavy wire. The rectifier should be bolted to the chassis to keep cool. If the charger have a high/low switch it’s a bonus, if not you can in some cases add a few turns of wire on the secondary winding. The circuit; a 14-stage ripple counter and oscillator IC 4060 produce a pulse, which is the heartbeat of the circuit. The pulse is feed to the 555 timer that deicide the length of the active output. With the switch you can select long or short pulse output. The output of the 555 timer triggers the zero-cross optoisolator triac driver MOC 3041 via a transistor. This gives the charger transformer a soft start via the triac and the snubber circuit. A small power supply is necessary for the circuit and consists of T1 a transformer 15V 0.1A secondary, a bridge rectifier, a regulator and two caps. Because this project include a charger that is (X) the outcome can differ in performance from one case to another. However this do not mean that your project doesn’t work, but the efficiency can vary. Some notes the snubbercap is a high voltage AC type (X) and the resistors on the mains side is at least 0.5W type. Use a triac that can take 400V+ and 10A+, I use BTA 25.600 but this is overkill in most cases. No PCB sorry! How it works:Well the short version. The object is to get the cell voltage high enough for the sulphate to dissolve without boiling or melting the battery. This is achieved by applying higher voltage for shorter periods and let the battery rest for a while. The pulses on short range is about 0.5s on / 3s off and the long pulse range is 1.4s on / 2s off. These times can vary depending on component tolerances. Start on long pulse and if you discover “boiling” (more than with normal charging) in the electrolyte switch to short puls. Don’t leave the process unattended, at least until you know how your specific version of this project turns out. I built ver.1 of this circuit some 10 years ago and have experimented with it but I’m sure someone can improve it further.   (View)

View full Circuit Diagram | Comments | Reading(1007)

Automotive 12V to +-20V converter (for audio amplifier)

Published:2013/7/15 20:27:00 Author:muriel | Keyword: Automotive , 12V to +-20V , converter , audio amplifier

Automotive 12V to +-20V converter (for audio amplifier)

Microsoft VBScript ÔËÐÐʱ´íÎó ´íÎó '800a000d'

ÀàÐͲ»Æ¥Åä: 'objRegExp.Execute'

/include/common.asp£¬ÐÐ 1271