Want to post a buying lead? If you are not a member yet, please select the specific/related part number first and then fill the quantity and your contact details in the "Request for Quotation Form" on the left, and then click "Send RFQ".Your buying lead can then be posted, and the reliable suppliers will quote via our online message system or other channels soon.
The ADM1070 is a negative voltage hot swap controller that allows a board to be safely inserted and removed from a live 48 V backplane. The part achieves this by providing robust current limiting, protection against transient and nontransient short circuits and overvoltage and undervoltage conditions. The ADM1070 typically operates from a negative voltage of up to 80 V and can tolerate transient voltages of up to 200 V.
In-rush current is limited to a programmable value by controlling the gate drive of an external N-channel FET. The current limit can be controlled by the choice of the sense resistor, RSENSE. Added control of the in-rush current is provided by an on-chip timer that uses pulsewidth modulation to allow the maximum current to flow for only 3% of the time. An autorestart occurs after a current limit timeout. After seven successive autorestarts, the fault will be latched and the part goes into shutdown with the result that the external FET is disabled until the power is reset.
The ADM1070 also features single-pin undervoltage and over-voltage detection. The FET is turned off if a nontransient voltage less than the undervoltage threshold, typically 36 V, or greater than the overvoltage threshold, typically 77 V, is detected on the UV/OV Pin. The operating voltage window of the ADM1070 is programmable and is determined by the ratio R1/R2. Time filtering on the undervoltage and overvoltage detection and current limiting is programmable via the TIMER Pin. An external capacitor connected between the TIMER Pin and VEE determines the undervoltage/overvoltage time filter and the timeout in current limit. If the pin is tied to VEE, the time filter values and the current limit timeout revert to default figures. The ADM1070 is fabricated using BiCMOS technology for minimal power consumption. The part is available in a small 6-Lead SOT-23 package.
ADM1070 Maximum Ratings
Supply Voltage (VDDVEE) . . . . . . . . . . . . . 0.3 V to 200.0 V Maximum Shunt Supply Voltage, VSS . . . . . . . . . . . . . . . 16 V SENSE Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 V to +16 V GATE Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.3 V to +16 V UV/OV Pin . . . . . . . . . . . . . . . . . . . . . . . . . . 0.3 V to +15 V TIMER Pin . . . . . . . . . . . . . . . . . . . . . . . . . . 0.3 V to +10 V Maximum Junction Temperature . . . . . . . . . . . . . . . . .125°C Temperature Range . . . . . . . . . . . . . . . . . . 40°C to +85°C Continuous Power Dissipation . . . . . . . . . . . . . . . . 282 mW Storage Temperature Range . . . . . . . . . . .65°C to +150°C Lead Temperature (Soldering, 10 sec) . . . . . . . . . . . . 300°C
ADM1070 Features
Allows Safe Board Insertion and Removal from a Live 48 V Backplane Typically Operates from 36 V to 80 V Tolerates Transients up to 200 V (Limited by External Components) Accurate Programmable Linear Current Limit for In-Rush Control and Short Circuit Protection Programmable Timeout in Current Limit Limited Consecutive Retry: Auto-Restart after Current Limit Timeout Shutdown after Seven Consecutive Auto Restarts Provides Immunity from Step Induced Current Spikes Default Timing Provided with no TIMER Capacitor Single Pin Undervoltage/Overvoltage Detection Programmable Operating Voltage Window Programmable Undervoltage/Overvoltage Time Filter Small 6-Lead SOT-23 Package
ADM1070 Typical Application
Central Office Switching 48 V Distributed Power Systems Negative Power Supply Control Hot Board Insertion Electronic Circuit Breaker High Availability Servers Programmable Current Limiting Circuit 48 V Power Supply Modules