UAA2068, UAA2068A, UAA2068AHL Selling Leads, Datasheet
MFG:PHILIPS Package Cooled:650 D/C:03/04+
UAA2068, UAA2068A, UAA2068AHL Datasheet download

Part Number: UAA2068
MFG: PHILIPS
Package Cooled: 650
D/C: 03/04+
MFG:PHILIPS Package Cooled:650 D/C:03/04+
UAA2068, UAA2068A, UAA2068AHL Datasheet download

MFG: PHILIPS
Package Cooled: 650
D/C: 03/04+
Want to post a buying lead? If you are not a member yet, please select the specific/related part number first and then fill the quantity and your contact details in the "Request for Quotation Form" on the left, and then click "Send RFQ".Your buying lead can then be posted, and the reliable suppliers will quote via our online message system or other channels soon.
TOP
PDF/DataSheet Download
Datasheet: UAA2068
File Size: 135750 KB
Manufacturer: PHILIPS [Philips Semiconductors]
Download : Click here to Download
PDF/DataSheet Download
Datasheet: UAA2068AHL
File Size: 124842 KB
Manufacturer: PHILIPS [Philips Semiconductors]
Download : Click here to Download
PDF/DataSheet Download
Datasheet: UAA2068AHL
File Size: 124842 KB
Manufacturer: PHILIPS [Philips Semiconductors]
Download : Click here to Download
The UAA2068AHL BiCMOS device integrates a 950 MHz VCO, a frequency doubler, main and reference dividers and a phase comparator, to implement a phase-locked loop for DECT channel frequencies. The 1.9 GHz signal is buffered and switched, in TX mode, to drive the transmit power amplifier (CGY20xx series) or, in RX mode, to be used as an LO signal for the receiver mixer IC (UAA3540TS).
The synthesizer's main divider is driven by the frequency doubler output in the range from 1880 to 1920 MHz and programmed via a 3-wire serial bus.The reference divider ratio is fixed at 16. Outputs of the main and reference dividers drive a phase comparator where a charge pump produces phase error current pulses for integration in an external loop filter. Only a passive loop filter is necessary. The charge-pump current (phase comparator gain) is set by an external resistor (RSET) at pin RSET.
The VCO is powered from an internally regulated voltage source and includes internal varicap diodes. Its tuning range is wider than the required band to allow for production spreads. In a Time Division Multiple Access (TDMA) system such as DECT, the VCO and the synthesizer are switched on one slot before the required one to lock the VCO to the required channel frequency.Just before the required slot, the synthesizer is switched off, allowing open-loop modulation of the VCO during transmission. When opening the loop, the frequency pulling (due to switching off the synthesizer) can be maintained within the DECT specification.
The device is designed to operate from 3 NiCd cells in pocket phones, with low current and nominal 3.6 V supplies. Separate power and ground pins are provided to the different parts of the circuit. The ground leads should be short-circuited externally to prevent large currents flowing across the die and thus causing damage.
All supply pins (VCC) must also be at the same potential,except VCC(CP) which can be equal to or greater than the other supply pins (e.g. VCC = 3 V and VCC(CP) = 5 V for wider VCO control voltage range).
|
SYMBOL |
PARAMETER |
CONDITIONS |
MIN. |
MAX. |
UNIT |
|
VCC |
supply voltage |
-0.3 |
+5.5 |
V | |
|
VCC(CP) |
charge-pump supply voltage |
-0.3 |
+5.5 |
V | |
|
VCC(CP)-VCC |
difference in voltage between VCC(CP) and VCC |
-0.3 |
+5.5 |
V | |
|
GND |
difference in ground supply voltage applied between all ground pins |
note 1 |
- |
0.3 |
V |
|
Ptot |
total power dissipation |
- |
275 |
mW | |
|
Tstg |
storage temperature |
-55 |
+125 |
| |
|
Tamb |
operating ambient temperature |
-10 |
+60 |
| |
|
Tj |
junction temperature |
- |
150 |
|

