Want to post a buying lead? If you are not a member yet, please select the specific/related part number first and then fill the quantity and your contact details in the "Request for Quotation Form" on the left, and then click "Send RFQ".Your buying lead can then be posted, and the reliable suppliers will quote via our online message system or other channels soon.
The Genesys Logic GL600USB microcontroller is optimized for USB 2D/3D/4D mouse. This USB microcontroller conforms to the low-speed (1.5Mbps) requirements of the USB Specification version 1.1. The microcontroller is a self-contained unit with an USB SIE, an USB transceiver, an 8-bits RISC-like microcontroller, a timer, data and program memories. It supports one USB device address and two endpoints (include endpoint 0).
GL600USB Maximum Ratings
Symbol
Characteristic
Value
Unit
TSTG
Storage temperature
-55 to +150
TOP
Operating temperature
0 to +70
VCC
Supply voltage
-0.5 to +7.0
V
VIN
DC input voltage
-0.5 to +VDD + 0.5
V
I
Maximum current per pin excluding VDD and VSS
25
mA
IMGND
Maximum current out of GND
100
mA
IMVCC
Maximum current out of VCC
100
mA
VESD
Static discharge voltage
>4000
V
GL600USB Features
Low-cost solution for low-speed USB mouse 8-bit micro-controller - Operation Speed: DC to 6MHz clock input - Performance: 3 MIPS @ 6MHz - Single cycle instruction execution - RISC-like architecture - USB optimized instruction set USB Specification Compliance - Conforms to USB 1.5Mbps Specification, Version 1.1 - Conforms to USB HID Class Specification, Version 1.1 - Supports 1 device address and 2 endpoints (include endpoint 0) I/O ports - Up to 13(GL600USB)/11(GL600USB-A)/9(GL600USB-B) general purpose I/O pins (OTP type is less a GPIO pin than mask type) - Internal RC clock to wakeup periodically (about 500ms) when suspend - Up to 8(GL600USB)/6(GL600USB-A)/4(GL600USB-B) special purpose I/O pins optimized for photo-sensor (Internal build in 4 bits ADC) - Up to 2 I/O pins with large current drive capability to drive LED (Sink current up to 16 mA) Internal memory - 64 bytes of RAM (special purpose register is not included) - 1.75K x 14 of program ROM Integrated USB transceiver Patented full-range detection for photo-sensor - Removes the expensive process of matching LED and photo-sensor On-chip 3.3v output - No external regulator required Improved output drivers with slew-rate control to reduce EMI 6 MHz external clock Internal power-on reset(POR) Internal power-fail detector Supports suspend/normal mode power management - Suspend current lower than 400mA for whole mouse system (mask type) 8-bits free-running timer Available in cost saving 20-pin(GL600USB) PDIP, 18-pin(GL600USB-A) PDIP and 16-pin(GL600USB-B) PDIP
GL600USB Connection Diagram
GL600USB-A General Description
The Genesys Logic GL600USB microcontroller is optimized for USB 2D/3D/4D mouse. This USB microcontroller conforms to the low-speed (1.5Mbps) requirements of the USB Specification version 1.1. The microcontroller is a self-contained unit with an USB SIE, an USB transceiver, an 8-bits RISC-like microcontroller, a timer, data and program memories. It supports one USB device address and two endpoints (include endpoint 0).
GL600USB-A Maximum Ratings
Symbol
Characteristic
Value
Unit
TSTG
Storage temperature
-55 to +150
TOP
Operating temperature
0 to +70
VCC
Supply voltage
-0.5 to +7.0
V
VIN
DC input voltage
-0.5 to +VDD + 0.5
V
I
Maximum current per pin excluding VDD and VSS
25
mA
IMGND
Maximum current out of GND
100
mA
IMVCC
Maximum current out of VCC
100
mA
VESD
Static discharge voltage
>4000
V
GL600USB-A Features
Low-cost solution for low-speed USB mouse 8-bit micro-controller - Operation Speed: DC to 6MHz clock input - Performance: 3 MIPS @ 6MHz - Single cycle instruction execution - RISC-like architecture - USB optimized instruction set USB Specification Compliance - Conforms to USB 1.5Mbps Specification, Version 1.1 - Conforms to USB HID Class Specification, Version 1.1 - Supports 1 device address and 2 endpoints (include endpoint 0) I/O ports - Up to 13(GL600USB)/11(GL600USB-A)/9(GL600USB-B) general purpose I/O pins (OTP type is less a GPIO pin than mask type) - Internal RC clock to wakeup periodically (about 500ms) when suspend - Up to 8(GL600USB)/6(GL600USB-A)/4(GL600USB-B) special purpose I/O pins optimized for photo-sensor (Internal build in 4 bits ADC) - Up to 2 I/O pins with large current drive capability to drive LED (Sink current up to 16 mA) Internal memory - 64 bytes of RAM (special purpose register is not included) - 1.75K x 14 of program ROM Integrated USB transceiver Patented full-range detection for photo-sensor - Removes the expensive process of matching LED and photo-sensor On-chip 3.3v output - No external regulator required Improved output drivers with slew-rate control to reduce EMI 6 MHz external clock Internal power-on reset(POR) Internal power-fail detector Supports suspend/normal mode power management - Suspend current lower than 400mA for whole mouse system (mask type) 8-bits free-running timer Available in cost saving 20-pin(GL600USB) PDIP, 18-pin(GL600USB-A) PDIP and 16-pin(GL600USB-B) PDIP