Want to post a buying lead? If you are not a member yet, please select the specific/related part number first and then fill the quantity and your contact details in the "Request for Quotation Form" on the left, and then click "Send RFQ".Your buying lead can then be posted, and the reliable suppliers will quote via our online message system or other channels soon.
The PM20CNJ060 has some maximum ratings (Tj = 25, unless otherwise noted).When parameter is collector-emitter voltage,the symbol is VCES,the condition is VD = 15V, VCIN = 15V,the ratings is 600,the unit is V.When parameter is collector current,the symbol is ±IC,the condition is TC = 25,the ratings is 20,the unit is A.When parameter is collector current(peak),the symbol is ±ICP,the condition is TC = 25,the ratings is 40,the unit is A.When parameter is collector dissipation,the symbol is PC,the condition is TC = 25,the ratings is 56,the unit is W.When parameter is junction temperature,the symbol is Tj,the ratings is -20 to +125,the unit is .
The item defines the maximum junction temperature for the power elements (IGBT/Diode) of the IPM to ensure safe operation. However,these power elements can endure junction temperature as high as 150°C instantaneously. To make use of this additional temperature allowance,a detailed study of the exact application conditions is required and, accordingly, necessary information is requested to be provided before use.
Design the PCB pattern to minimize wiring length between opto-coupler and IPM's input terminal, and also to minimize the stray capacity between the input and output wirings of opto-coupler.Connect low impedance capacitor between the Vcc and GND terminal of each fast switching opto-coupler.Fast switching opto-couplers:tPLH, tPHL 0.8s, Use High CMR type.Slow switching opto-coupler:CTR > 100%.Use 4 isolated control power supplies (VD). Also, care should be taken to minimize the instantaneous voltage charge of the power supply.Make inductance of DC bus line as small as possible, and minimize surge voltage using snubber capacitor between P and N terminal.Use line noise filter capacitor (ex. 4.7nF) between each input AC line and ground to reject common-mode noise from AC line and improve noise immunity of the system.
PM20CNJ060 Maximum Ratings
PM20CNJ060 Features
PM20CSJ060 Parameters
Technical/Catalog Information
PM20CSJ060
Vendor
Powerex Inc
Category
Integrated Circuits (ICs)
Package / Case
Module
Mounting Type
Screw Mount
Type
3 Phase
Voltage - Supply
13.5 V ~ 16.5 V
On-State Resistance
-
Current - Output / Channel
20A
Current - Peak Output
40A
Packaging
Bulk
Input Type
Inverting
Number of Outputs
3
Operating Temperature
-20°C ~ 100°C
Lead Free Status
Contains Lead
RoHS Status
RoHS Non-Compliant
Other Names
PM20CSJ060 PM20CSJ060
PM20CSJ060 General Description
Powerex Intellimod™ Intelligent Power Modules are isolated base modules designed for power switching applications operating at frequencies to 20kHz. Built-in control circuits provide optimum gate drive and protection for the IGBT and free-wheel diode power devices.
PM20CSJ060 Maximum Ratings
Characteristics
Symbol
PM20CSJ060
Units
Power Device Junction Temperature
Tj
-20 to 150
°C
Storage Temperature
Tstg
-40 to 125
°C
Case Operating Temperature
TC
-20 to 100
°C
Mounting Torque, M4 Mounting Screws
-
13
in-lb
Module Weight (Typical)
-
60
Grams
Supply Voltage Protected by OC and SC (VD = 13.5 - 16.5V, Inverter Part)
VCC(prot.)
400
Volts
Isolation Voltage, AC 1 minute, 60Hz Sinusoidal
VRMS
2500
Volts
PM20CSJ060 Features
`Complete Output Power Circuit `Gate Drive Circuit `Protection Logic Short Circuit Over Current Over Temperature Under Voltage
PM20CSJ060 Typical Application
·Inverters ·UPS ·Motion/Servo Control ·Power Supplies