ADA4851-1YRJZ-R2

Series: -
Type: -
Max Output Power x Channels @ Load: -
Voltage - Supply: -
Features: -
Mounting Type: Surface Mount
Operating Temperature: -40°C ~ 125°C
Number of Circuits: 1
Output Type: Rail-to-Rail
Package / Case: SOT-23-6
Supplier Device Package: SOT-23-6
Gain Bandwidth Product: -
Voltage - Supply, Single/Dual (±): 2.7 V ~ 12 V, ±1.35 V ~ 6 V
Packaging: Cut Tape (CT)
Amplifier Type: Voltage Feedback
Voltage - Input Offset: 600µV
Manufacturer: Analog Devices Inc
Slew Rate: 375 V/µs
-3db Bandwidth: 105MHz
Current - Input Bias: 2.2µA
Current - Supply: 2.9mA
Current - Output / Channel: 83mA


Description

The ADA4851-1YRJZ-R2 is one member of the ADA4851-1 series.The ADA4851 family is designed to operate at supply voltages as low as +3 V and up to ±5 V. These parts provide true single-supply capability, allowing input signals to extend 200 mV below the negative rail and to within 2.2 V of the positive rail. On the output, the amplifiers can swing within 60 mV of either supply rail.

Features of the ADA4851-1YRJZ-R2 are:(1)0.1 dB flatness: 11 MHz;(2)differential gain: 0.08%;(3)differential phase: 0.09°;(4)fully specified at +3 V, +5 V, and ±5 V supplies;(5)rail-to-rail output output swings to within 60 mV of either rail;(6)low voltage offset: 0.6 mV;(7)wide supply range: 3 V to 10 V;(8)low power: 2.5 mA/amplifier;(9)power-down mode.The amplifiers do not exhibit phase reversal, even for input voltages beyond the voltage supply rails. Going more than 0.6 V beyond the power supplies turns on protection diodes at the input stage, which greatly increases the current draw of the devices.

The absolute maximum ratings of the ADA4851-1YRJZ-R2 can be summarized as:(1)supply voltage:12.6 V; (2)power dissipation:see figure 5; (3)common-mode input voltage:-VS-0.5 V to +VS + 0.5 V; (4)differential input voltage:+VS to -VS; (5)storage temperature:-65 to +125; (6)operating temperature range:-40 to +125; (7)lead temperature range:JEDEC J-STD-20; (8)junction temperature:150.Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.For signals approaching the minus supply and inverting gain and high positive gain configurations, the headroom limit is the output stage.The ADA4851-1 amplifiers use a common emitter output stage. This output stage maximizes the available output range, limited by the saturation voltage of the output transistors. The saturation voltage increases with the drive current that the output transistor is required to supply due to the output transistor's collector resistance.

Parameters:

Technical/Catalog Information	ADA4851-1YRJZ-R2
Vendor	Analog Devices Inc (VA)
Category	Integrated Circuits (ICs)
Packaging	Digi-Reel?
Amplifier Type	Voltage Feedback
Number of Circuits	1 - Single
Package / Case	SOT-23-6
Slew Rate	375 V/s
Gain Bandwidth Product	-
Current - Supply	2.9mA
Current - Output / Channel	125mA
Voltage - Supply, Single/Dual (±)	2.7 V ~ 12 V, ±1.35 V ~ 6 V
Output Type	Rail-to-Rail
-3db Bandwidth	105MHz
Current - Input Bias	2.2A
Operating Temperature	-40°C ~ 125°C
Voltage - Input Offset	600V
Drawing Number	*
Lead Free Status	Lead Free
RoHS Status	RoHS Compliant
Other Names	ADA4851 1YRJZ R2 ADA48511YRJZR2 ADA4851 1YRJZR2DKR ND ADA48511YRJZR2DKRND ADA4851-1YRJZR2DKR