HCPL-0534

Maximum Reverse Diode Voltage : 5 V
Maximum Power Dissipation : 45 mW
Maximum Operating Temperature : + 100 C
Packaging : Tube
Maximum Input Diode Current : 25 mA
Package / Case : SOIC-8
Maximum Forward Diode Voltage : 1.7 V
Minimum Operating Temperature : - 55 C
Maximum Baud Rate : 1 Mbps
Current Transfer Ratio : 27 %


Features:

• 15 kV/ms Minimum Common Mode Transient Immunity at V_CM = 1500 V (HCPL-4534/0534)
• High Speed: 1 Mb/s
• TTL Compatible
• Available in 8 Pin DIP, SO-8, and 8 Pin DIP Gull Wing Surface Mount (Option 020) Packages
• High Density Packaging
• 3 MHz Bandwidth
• Open Collector Outputs
• Guaranteed Performance from 0 to 70
• Safety Approval UL Recognized 2500 V rms for 1 minute (5000 V rms for 1 minute for Option 020) per UL1577 CSA Approved
• Single Channel Version Available (4502/3, 0452/3)
• MIL-STD-1772 Version Available (55XX/65XX/4N55)

Application

• Line Receivers High Common Mode Transient Immunity (>1000 V/ms) and Low Input-Output Capacitance (0.6 pF)
• High Speed Logic Ground Isolation
TTL/TTL, TTL/ LTTL, TTL/CMOS, TTL/LSTTL
• Replace Pulse Transformers
Save Board Space and Weight
• Analog Signal Ground Isolation
Integrated Photon Detector Provides Improved Linearity over Phototransistor Type
• Polarity Sensing
• Isolated Analog Amplifier
Dual Channel Packaging Enhances Thermal Tracking

Specifications

Parameter	Symbol	Device	Min.	Max.	Units	Note
Storage Temperature	TS		55	125
Operating Temperature†	TA		- 55	100
Average Forward Input Current (each channel)	IF(AVG)			25	mA
Peak Forward Input Current (each channel) (50% duty cycle, 1 ms pulse width)	IF(PEAK)			50	mA
Peak Transient Input Current (each channel) (£1 ms pulse width, 300 pps)	IF(TRANS)			5	A
Reverse LED Input Voltage (each channel)	VR			1	V
Input Power Dissipation (each channel)	PIN			45	mW
Average Output Current (each channel)	IO(AVG)			8	mA
Peak Output Current	IO(PEAK)			16	mA
Supply Voltage (Pin 8-5)	VCC		-0.5	30	V
Output Voltage (Pins 7-5, 6-5)	VO		-0.5	20	V
Output Power Dissipation (each channel)	PO			35	mW	13
Lead Solder Temperature (Through-Hole Parts Only) 1.6 mm below seating plane, 10 seconds	TLS	8-Pin DIP		260
Reflow Temperature Profile	TRP	SO-8 and Option 300	See Package Outline Drawings section

Description

This HCPL-0534 dual channel optocoupler contains a pair of light emitting diodes and integrated photodetectors with electrical insulation between input and output. Separate connection for the photodiode bias and output transistor collectors increase the speed up to a hundred times that of a conventional phototransistor coupler by reducing the base-collector capacitance.

HCPL-0534 is available in an industry standard SO-8 package. It is an HCPL-0531 with increased common mode transient immunity of 15,000 V/ms minimum at VCM = 1500 V guaranteed.

These HCPL-0534 dual channel optocouplers contain a pair of light emitting diodes and integrated photodetectors with electrical insulation between input and output.

Separate connection for the HCPL-0534 photodiode bias and outputtransistor collectors increase thespeed up to a hundred times that ofa conventional phototransistor coupler by reducing the basecollector capacitance.

Parameters:

Technical/Catalog Information	HCPL-0534
Vendor	Avago Technologies US Inc.
Category	Isolators
Voltage - Isolation	3750Vrms
Input Type	DC
Output Type	Transistor with Vcc
Current - Output / Channel	8mA
Voltage - Output	20V
Vce Saturation (Max)	-
Current Transfer Ratio (Min)	19% @ 16mA
Mounting Type	Surface Mount
Package / Case	8-SOIC
Packaging	Tube
Number of Circuits	2 - Dual
Lead Free Status	Contains Lead
RoHS Status	RoHS Non-Compliant
Other Names	HCPL 0534 HCPL0534 516 1047 5 ND 51610475ND 516-1047-5