HCPL-0700

Maximum Reverse Diode Voltage : 5 V
Packaging : Tube
Package / Case : SOIC-8
Maximum Forward Diode Voltage : 1.7 V
Maximum Input Diode Current : 20 mA
Maximum Baud Rate : 100 KBps
Maximum Power Dissipation : 135 mW
Maximum Operating Temperature : + 70 C
Minimum Operating Temperature : 0 C
Current Transfer Ratio : 2600 %


Features:

Low input current 0.5 mA
Superior CTR 2000%
Superior CMR 10 kV/s
CTR guaranteed 0-70°C
U.L. Recognized (file# E90700)
VDE 0884 recognized (file# 136616)
approval pending for HCPL-0730/0731
BSI recognized (file# 8661, 8662)
HCPL-0700/0701 only

Application

Digital logic ground isolation
Telephone ring detector
EIA-RS-232C line receiver
High common mode noise
line receiver
P bus isolation
Current loop receiver




Specifications

ABSOLUTE MAXIMUM RATINGS (TA = 25°C unless otherwise specified)
rameter		Symbol	Value	Units
Storage Temperature		TSTG	-40 to +125	oC
Operating Temperature		TSTG	-40 to +85	oC
Reflow Temperature Profile (Refer to fig. 11)
EMITTER
DC/Average Forward Input Current		IF(avg)	20	mA
Peak Forward Input Current (50% duty cycle, 1 ms P.W.)		IF (pk)	40	mA
Peak Transient Input Current - (1 s P.W., 300 pps)		IF (trans)	1.0	A
Reverse Input Voltage		VR	5	V
Input Power Dissipation		PD	35	mW
ETECTOR
Average Output Current (Pin 6)		IO (avg)	60	mA
Emitter-Base Reverse Voltage	HCPL-0700/HCPL-0701	VEBR	0.5	V
Supply Voltage, Output Voltage	HCPL-0700/HCPL-0730	VCC ,VO	-0.5 to 7	V
	HCPL-0701/HCPL-0731		-0.5 to 18
Output power dissipation		PD	100	mW

Description

This HCPL-0700 high gain series coupler uses a Light Emitting Diode and an integrated high gain photodetector to provide extremely high current transfer ratio between input and output. Separate pins for the photodiode and output stage result in TTL compatible saturation voltages and high speed operation. Where desired VCC and VO terminals may be tied together to achieve convention photodarlington operation.A base access terminal allows a gain bandwidth adjustment to be made.

The HCPL-0700 is designed for use mainly in TTL applications. Current transfer ratio (CTR) is 300% minimum over 0 to 70 degrees C for an LED current of 1.6 mA (1 TTL Unit load). A 300% minimum CTR enables operation with 1 TTL Load using a 2.2 k ohm pull-up resistor. Selection for lower input current down to 250 mA is available upon request.

The HCPL-0700 is a surface mount device packaged in an industry standard SOIC-8 footprint. The SOIC-8 does not require "through holes" in a PCB. This package occupies approximately one-third the footprint area of the standard dual-in-line package. The lead profile is designed to be compatible with standard surface mount processes.

The HCPL-0700, HCPL-0701, HCPL-0730 and HCPL-0731 optocouplers consist of an AlGaAs LED optically coupled to a high gain split darlington photodetector housed in a compact 8-pin small outline package. The HCPL-0730 and HCPL-0731 devices have two channels per package for optimum mounting density.
The HCPL-0700 split darlington configuration separating the input photodiode and the first stage gain from the output transistor permits lower output saturation voltage and higher speed operation than possible with conventional darlington phototransistor optocoupler. The combination of a very low input current of 0.5 mA and a high current transfer ratio of 2000% makes this family particularly useful for input interface to MOS, CMOS, LSTTL and EIA RS232C, while output compatibility is ensured to CMOS as well as high fan-out TTL requirements.




Parameters:

Technical/Catalog Information	HCPL-0700
Vendor	Avago Technologies US Inc.
Category	Isolators
Isolation Voltage	3750Vrms
Input Type	DC
Output Type	Darlington with Vcc
Current - Output/Channel	60mA
Voltage - Output	18V
Vce Saturation (Max)	-
Current Transfer Ratio (Min)	300% @ 1.6mA
Mounting Type	Surface Mount
Package / Case	8-SOIC
Packaging	Tube
Number of Circuits	1 - Single
Lead Free Status	Contains Lead
RoHS Status	RoHS Non-Compliant
Other Names	HCPL 0700 HCPL0700 516 1008 5 ND 51610085ND 516-1008-5