HCPL-2430

Current Transfer Ratio :
Maximum Input Diode Current :
Packaging : Tube
Maximum Forward Diode Voltage : 1.5 V
Maximum Operating Temperature : + 70 C
Minimum Operating Temperature : 0 C
Maximum Baud Rate : 40 MBps
Maximum Reverse Diode Voltage : 2 V
Maximum Power Dissipation : 350 mW
Package / Case : PDIP-8


Features:

• High Speed: 40 MBd Typical
Data Rate
• High Common Mode Rejection: HCPL-2400: 10 kV/ms at VCM = 300 V (Typical)
• AC Performance Guaranteed over Temperature
• High Speed AlGaAs Emitter
• Compatible with TTL, STTL, LSTTL, and HCMOS Logic Families
• Totem Pole and Tri State Output (No Pull Up Resistor Required)
• Safety Approval UL Recognized 2500 V rms for 1 minute per UL1577 VDE 0884 Approved with VIORM = 630 V peak (Option 060) for HCPL-2400 CSA Approved
• High Power Supply Noise Immunity
• MIL-STD-1772 Version Available (HCPL-5400/1 and HCPL-5430/1)




Application

• Isolation of High Speed Logic Systems
• Computer-Peripheral Interfaces
• Switching Power Supplies
• Isolated Bus Driver (Networking Applications)
• Ground Loop Elimination
• High Speed Disk Drive I/O
• Digital Isolation for A/D, D/A Conversion
• Pulse Transformer Replacement




Pinout

Specifications

Parameter	Symbol	Minimum	Maximum	Units	Note
Storage Temperature	TS	-55	125	°C
Operating Temperature	TA	-40	85	°C
Average Forward Input Current	I F(AVG)		10	mA
Peak Forward Input Current	IFPK		20	mA	12
Reverse Input Voltage	VR		2	V
Three State Enable Voltage (HCPL-2400 Only)	VE	-0.5	10	V
Supply Voltage	VCC	-	7	V
Average Output Collector Current	IO	-25	25	mA
Output Collector Voltage	VO	-0.5	10	V
Output Voltage	VO	-0.5	18	V
Output Collector Power Dissipation (Each Channel)	PO		40	mW
Total Package Power Dissipation (Each Channel)	PT		350	mW
Lead Solder Temperature (for Through Hole Devices)	260°C for 10 sec., 1.6 mm below seating plane
Reflow Temperature Profile (Option #300)	See Package Outline Drawings section

Description

The HCPL-2430 high speed optocoupler combines an 820 nm AlGaAs light emitting diode with a high speed photodetector. This combination results in very high data rate capability and low input current. The three state output eliminates the need for a pull out resistor and allows for direct drive of data buses.

The HCPL-2430 detector has optical receiver input stage with built-in Schmitt trigger to provide logic compatible waveforms, eliminating the need for additional waveshaping. The hysteresis provides differential mode noise immunity and minimizes the potential for output signal chatter.

The electrical and switching characteristics of HCPL-2430  is guaranteed over the temperature range of 0^oC to 70^oC. This optocoupler is compatible with TTL, STTL, LSTTL, and HCMOS logic families. Typical data rates are 40 MBd.

Parameters:

Technical/Catalog Information	HCPL-2430
Vendor	Avago Technologies US Inc.
Category	Isolators
Mounting Type	Through Hole
Package / Case	8-DIP
Isolation Voltage	3750Vrms
Configuration	2, One Direction
Input Type	DC
Output Type	Open Collector
Data Rate	40Mbs
Current - Output/Channel	25mA
Packaging	Tube
Lead Free Status	Contains Lead
RoHS Status	RoHS Non-Compliant
Other Names	HCPL 2430 HCPL2430 516 1106 5 ND 51611065ND 516-1106-5