Features: • On-chip ROM capacities of 4, 6, and 8 kilobytes, and an on-chip RAM capacity of 384 *4 bits.
• Fully supports the LC66000 Series common instruction set (128 instructions). (The special-purpose instructions for TM1 and SI/01 are disabled.)
• I/O ports: 24 pins
• DTMF generator
This microcontroller incorporates a circuit that can generate two sine wave outputs, DTMF output.
• 8-bit serial interface: one circuit
• Instruction cycle time: 0.95 to 10 s (at 3.0 to 5.5 V)
• Powerful timer functions and prescalers
- Time limit timer, event counter, pulse width measurement, and square wave output using a 12-bit timer.
- Time base function using a 12-bit prescaler.
• Powerful interrupt system with 6 interrupt factors and 6 interrupt vector locations.
- External interrupts: 3 factors/3 vector locations
- Internal interrupts: 3 factors/3 vector locations
• Flexible I/O functions
Selectable options include 20-mA drive outputs, pull-up and open drain circuits.
• Optional runaway detection function (watchdog timer)
• 8-bit I/O functions
• Power saving functions using halt and hold modes.
• Packages: DIP30SD, MFP30S
• Evaluation ICs: LC665099 (evaluation chip) + EVA86K
- ECB662500
LC66E2108(on-chip EPROM microcontroller)
Pinout
Specifications
|
Parameter |
Symbol |
Conditions |
Ratings |
Unit |
Note |
| Maximum supply voltage |
VDD max |
VDD |
0.3 to +7.0 |
V |
|
| Input voltage |
VIN1 |
P2, P3 (except for the P33/HOLD pin),P4, P51, and P53 |
0.3 to +15.0 |
V |
1 |
|
VIN2 |
All other inputs |
0.3 to VDD + 0.3 |
V |
2 |
| Output voltage |
VOUT1 |
P2 and P3 (except for the P33/HOLD pin) |
0.3 to +15.0 |
V |
1 |
|
VOUT2 |
All other inputs |
0.3 to VDD + 0.3 |
V |
2 |
| Output current per pin |
ION1 |
P0, P1, P2, P3 (except for the P33/HOLD pin),P4, P5 |
20 |
mA |
3 |
|
IOP1 |
P0, P1, P4, P5 |
2 |
mA |
4 |
|
IOP2 |
P2, P3 (except for the P33/HOLD pin) |
4 |
mA |
4 |
| Total pin current |
ION1 |
P1, P2, P3 (except for the P33/HOLD pin) |
75 |
mA |
3 |
|
ION2 |
P0, P4, P5 |
75 |
mA |
3 |
|
IOP1 |
P1, P2, P3 (except for the P33/HOLD pin) |
25 |
mA |
4 |
|
IOP2 |
P0, P4, P5 |
25 |
mA |
4 |
| Allowable power dissipation |
Pd max |
Ta = 30 to +70°C: DIP30S (MFP30S) |
340(200) |
mW |
5 |
| Operating temperature |
Topr |
|
-30to+70 |
°C |
|
| Storage temperature |
Tstg |
|
-55to+125 |
°C |
|
Note: 1. Applies to pins with open-drain output specifications. For pins with other than open-drain output specifications, the ratings in the pin column for that pin apply.
2. For the oscillator input and output pins, levels up to the free-running oscillation level are allowed.
3. Sink current
4. Source current
5. We recommend the use of reflow soldering techniques to solder mount MFP packages.
Please consult with your Sanyo representative for details on process conditions if the package itself is to be directly immersed in a dip-soldering bath (dip-soldering techniques).
DescriptionThe LC662104A, LC662106A, and LC662108A are 4-bit CMOS microcontrollers that integrate on a single chip all the functions required in a special-purpose telephone controller, including ROM, RAM, I/O ports, a serial interface, a DTMF generator, timers, and interrupt functions. These microcontrollers are available in a 30-pin package
LC662104A Data Sheet
