Features: Complies with DECT ETS 300 175-2,3 & 8 SWAP-CA V1.3 Rev 1.3 20000616 1.8Volt operating voltage with 2.65V (typ) IO pads. Two chip low drop voltage regulators 16 bit CompactRISCTM CR16C Microprocessor with programmable clock speeds up to 20.736 MHz. Four channel DMA controller. Seria...
SC14428: Features: Complies with DECT ETS 300 175-2,3 & 8 SWAP-CA V1.3 Rev 1.3 20000616 1.8Volt operating voltage with 2.65V (typ) IO pads. Two chip low drop voltage regulators 16 bit CompactRISCTM CR16...
SeekIC Buyer Protection PLUS - newly updated for 2013!
268 Transactions
All payment methods are secure and covered by SeekIC Buyer Protection PLUS.
Complies with DECT ETS 300 175-2,3 & 8 SWAP-CA V1.3 Rev 1.3 20000616
1.8Volt operating voltage with 2.65V (typ) IO pads.
Two chip low drop voltage regulators
16 bit CompactRISCTM CR16C Microprocessor with programmable clock speeds up to 20.736 MHz.
Four channel DMA controller.
Serial Debug interface, Nexus Class-1 compliant.
16kbyte shared, 6kbyte non shared RAM
4kbyte shared RAM for TAM DSP
Versions with ROM, FLASH and data FLASH
Programmable 16 bits system bus interface with bus master and slave operation.
User programmable GENeric DSP with fixed telecom processing routines.
Four full duplex 32 kbits/sec ADPCM transcoder.
On-chip Dedicated Instruction Processor (DiP) for all TDMA based events, which supports DCT 1.152MHz, 0.576MHz and 0.288MHz data rates.
ISM band and DECT with 9.216, 10.368 and 13.824 MHz xtals.
Protected and unprotected full and double slot B-fields
Flexible 1.152 Mbit/sec three wire interface to radio front synthesizer.
One 16-bit linear CODEC
Selectable Fast Antenna Diversity operation or RSSI measurement with peak hold ADC.
Three input general purpose 8 bit ADC
Two general purpose timers and watch dog timer.
Two Capture timers for frequency measurement for e.g. metering, ringing and call progress tone detection.
Three general purpose I/O ports with two edge/level programmable interrupts
Full duplex UART and MICROWIRETM interface.
SPITM interface (Master/Slave).
Flexible 8 kHz synchronous Serial interface to external codecs and ISDN interface circuits.
Three programmable chip selects
Integrated opamp for caller-id
(80 pin PFQP and 80,)128,160 pins TQFP packages.
| Parameter | Description | Conditions | Min | Max | Units |
| Vbat1_max | Max Battery supply voltage VBAT1 | 5.5 | V | ||
| Vbat2_max | Max Battery supply voltage VBAT2 | 5.5 | V | ||
| Ibat1_max | Max negative current into VBAT1 | 300 | mA | ||
| Ibat2_max | Max negative current into VBAT2 | 300 | mA | ||
| Ivddiotot_max | Max total current into VDDIOs | 90 | mA | ||
| Ivddio_max | Max current through I/O pins | 20 | mA | ||
| Vdd_max | Max Core supply voltage (VDD-VSS / AVD-AVS / AVD2-AVS / VDDRF-VSSRF) |
2.0 | V | ||
| Vddiof_max | Max I/O Supply voltage for devices with FLASH (VDDIO-VSS) |
Note2 | 3.0 | V | |
| Vddio_max | Max I/O supply voltage for devices without FLASH (VDDIO-VSS) |
Note3 | 3.6 | V | |
| Vldo1_ctrl_max | Max voltage on pin LDO1_CTRL | Note4 | VSS-0.3 | 5.25 | V |
| Vldo2_ctrl_max | Max voltage on pin LDO2_CTRL | Note4 | VSS-0.3 | 5.25 | V |
| Vpon_max | Max voltage on pin PON | VSS-0.3 | 2.85 | V | |
| Vcharge_max | Max voltage on pin CHARGE | VSS-0.3 | 2.85 | V | |
| Vbat3_max | Max voltage on pin VBAT3 | VSS-0.3 | 2.85 | V | |
| Vadc1_max | Max voltage on pin ADC1 | VSS-0.3 | 2.85 | V | |
| Vrdidig_max | ax voltage on pin RDI digital mode (max 3.6V) | VSS-0.3 | VDDIO+0.3 | V | |
| Vrdiana_max | Max voltage on pin RDI analog mode | VSS-0.3 | 2.0 | V | |
| Vdig_max | Max voltage on digital Input pins (max 3.6V) | VSS-0.3 | VDDIO+0.3 | V | |
| Vana_max | Max voltage on any other input (incl analog pads) | VSS-0.3 | 2.0 | V | |
| Iprot_max | Max current through prot. diodes on any pin to VDDIO | 100 | mA | ||
| Iprotcid_max | Max current through prot. diode pins CID+/- to AGND | 1.0 | mA | ||
| Iprotmic_max | Current through prot. diode pin MIC+/- to AGND | 2.4 | mA | ||
| Iprotpon_max | Max current through prot. circuit of PON pin. | Note5 | 0.6 | mA | |
| Iprotcharge_max | Max current through prot. circuit of CHARGE pin. | Note5 | 0.6 | mA | |
| Iprotvbat3_max | Max current through prot. circuit of VBAT3 pin. | Note5 | 0.6 | mA | |
| Iprotadc1_max | Max current through prot. circuit of ADC1 pin. | 0.6 | mA | ||
| Tstorage | Storage temperature | -65 | +150 | °C | |
| Ppackage | Package power dissipation @ 25 °C | 500 | mW | ||
| Ilu | Latch-up current all pins according JEDEC 78 | TA = 65 °C | 100 | mA | |
| Ilu_rdi_25 | Latch-up current RDI pin | TA = 25 °C | 100 | mA | |
| Ilu_rdi_60 | Latch-up current RDI pin | TA = 65 °C | 50 | mA | |
| Vesd_mm | ESD voltage according to man machine model | 100 | V | ||
| Vesd_hbm | ESD voltage according to human body model | 1000 | V |
The SC14428 is a CMOS IC optimized to handle all the audio, signal and data processing needed within a DECT (1.9 GHz) or 2.4GHz ISM digital band base stations and handsets.
A four channel ADPCM transcoder, a very low power 16 bit Codec and Analog Frontend are integrated. Direct connections towards PSTN or ISDN line interface are possible.
The SC14428 has a programmable Generic DSP optimized for telecom applications.
The SC14428 is designed to fit to any radio interface. A dedicated TDMA controller handles all physical layer slot formats and radio control.
National Semiconductor's standard CompactRISCTM CR16C microprocessor takes care of all the higher protocol stack.