SN65MLVD080

Features:

`Low-Voltage Differential 30-Ω to 55-Ω Line Drivers and Receivers for Signaling Rates(1) Up to 250 Mbps; Clock Frequencies Up to 125MHz
` Meets or Exceeds the M-LVDS Standard TIA/EIA-899 for Multipoint Data Interchange
` Power Up/Down Glitch Free
` Controlled Driver Output Voltage Transition Times for Improved Signal Quality
` −1 V to 3.4 V Common-Mode Voltage Range Allows Data Transfer With 2 V of Ground Noise
` Bus Pins High Impedance When Driver Disabled or V_CC 1.5 V
` Independent Enables for each Driver
` Bus Pin ESD Protection Exceeds 8 kV
` Packaged in 64-Pin TSSOP (DGG)


Application

·Parallel Multipoint Data and Clock Transmission Via Backplanes and Cables
·Low-Power High-Speed Short-Reach Alternative to TIA/EIA-485
·Cellular Base Stations
·Central-Office Switches
·Network Switches and Routers


Pinout




Specifications

			SN65MLVD080, 082
Supply voltage range(2), VCC			−0.5 V to 4 V
Input voltage range	D, DE, RE		−0.5 V to 4 V
	A, B		−1.8 V to 4 V
Output voltage range	R		−0.3 V to 4 V
	A, or B		−1.8 V to 4 V
Storage temperature range	Human Body Model(3)	A, B	±8 kV
		All pins	±2 kV
	Charged-Device Model(4)	All pins	±1500 V
Continuous power dissipation			See Dissipation Rating Table
Storage temperature range			−65°C to 150°C

Description

The SN65MLVD080 and SN65MLVD082 provide eight half-duplex transceivers for transmitting and receiving Multipoint-Low-Voltage Differential Signals in full compliance with the TIA/EIA-899 (M-LVDS) standard, which are optimized to operate at signaling rates up to 250Mbps. The driver outputs of SN65MLVD080 and SN65MLVD082 have been designed to support multipoint buses presenting loads as low as 30-Ω and incorporates controlled transition times to allow for stubs off of the backbone transmission line.

The M-LVDS standard defines two types of receivers SN65MLVD080 and SN65MLVD082, designated as Type-1 and Type-2. Type-1 receivers (SN65MLVD080) have thresholds centered about zero with 25 mV of hysteresis to prevent output oscillations with loss of input; Type-2 receivers (SN65MLVD082) implement a failsafe by using an offset threshold. In addition, the driver rise and fall times are between 1 and 2.0 ns, complying with the M-LVDS SN65MLVD080 and SN65MLVD082 standard to provide operation at 250 Mbps while also accommodating stubs on the bus. Receiver outputs are slew rate controlled to reduce EMI and crosstalk effects associated with large current surges. The M-LVDS SN65MLVD080 and SN65MLVD082 standard allows for 32 nodes on the bus providing a high-speed replacement for RS-485 where lower common-mode can be tolerated or when higher signaling rates are needed.

The driver logic inputs and the receiver logic outputs of SN65MLVD080 and SN65MLVD082 are on separate pins rather than tied together as in some transceiver designs. The drivers have separate enables (DE) and the receivers are enabled globally through (RE). This arrangement of separate logic inputs, logic outputs, and enable pins allows for a listen-while-talking operation. The SN65MLVD080 and SN65MLVD082 are characterized for operation from −40°C to 85°C.