Purchase HIP4080A, In-stock HIP4080A From SeekIC.
Part Number: HIP4080A
Description: The HIP4080A is a high frequency, medium voltage Full Bridge N-Channel FET driver IC, available in 20 ...
- Table of contents:
HIP4080A
-
Suppliers
DataSheet
General Description
HIP4080A General Description
The HIP4080A is a high frequency, medium voltage Full Bridge N-Channel FET driver IC, available in 20 lead plastic SOIC and DIP packages. The HIP4080A includes an input comparator, used to facilitate the "hysteresis" and PWM modes of operation. Its HEN (high enable) lead can force current to freewheel in the bottom two external power MOSFETs, maintaining the upper power MOSFETs off. Since it can switch at frequencies up to 1MHz, the HIP4080A is well suited for driving Voice Coil Motors, switching amplifiers in class D high-frequency switching audio amplifiers and power supplies.
HIP4080A can also drive medium voltage brush motors, and two HIP4080As can be used to drive high performance stepper motors, since the short minimum "on-time" can provide fine micro-stepping capability.
Short propagation delays of approximately 55ns maximizes control loop crossover frequencies and dead-times which can be adjusted to near zero to minimize distortion, resulting in precise control of the driven load.
The similar HIP4081A IC allows independent control of all 4 FETs in an Full Bridge configuration.
The Application Note for the HIP4080A is AN9404.
HIP4080A Maximum Ratings
Supply Voltage, VDD and VCC. . . . . . . . . . . . . . . . . . . . -0.3V to 16V
Logic I/O Voltages . . . . . . . . . . . . . . . . . . . . . . . -0.3V to VDD +0.3V
Voltage on AHS, BHS. . ... -6.0V (Transient) to 80V (25oC to 125oC)
Voltage on AHS, BHS. .. . -6.0V (Transient) to 70V (-55oC to 125oC)
Voltage on ALS, BLS . . .. .. . . -2.0V (Transient) to +2.0V (Transient)
Voltage on AHB, BHB. . . . .. . . .VAHS, BHS -0.3V to VAHS, BHS +VDD
Voltage on ALO, BLO . . . . . .. . . . . . . VALS, BLS -0.3V to VCC +0.3V
Voltage on AHO, BHO . . . . . .. VAHS, BHS -0.3V to VAHB, BHB +0.3V
Input Current, HDEL and LDEL . . . . . . . . . . . . . . . . . . -5mA to 0mA
Phase Slew Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20V/ns
Logic I/O Voltages . . . . . . . . . . . . . . . . . . . . . . . -0.3V to VDD +0.3V
Voltage on AHS, BHS. . ... -6.0V (Transient) to 80V (25oC to 125oC)
Voltage on AHS, BHS. .. . -6.0V (Transient) to 70V (-55oC to 125oC)
Voltage on ALS, BLS . . .. .. . . -2.0V (Transient) to +2.0V (Transient)
Voltage on AHB, BHB. . . . .. . . .VAHS, BHS -0.3V to VAHS, BHS +VDD
Voltage on ALO, BLO . . . . . .. . . . . . . VALS, BLS -0.3V to VCC +0.3V
Voltage on AHO, BHO . . . . . .. VAHS, BHS -0.3V to VAHB, BHB +0.3V
Input Current, HDEL and LDEL . . . . . . . . . . . . . . . . . . -5mA to 0mA
Phase Slew Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20V/ns
HIP4080A Features
• Drives N-Channel FET Full Bridge Including High Side
Chop Capability
• Bootstrap Supply Max Voltage to 95VDC
• Drives 1000pF Load at 1MHz in Free Air at +50oC with
Rise and Fall Times of Typically 10ns
• User-Programmable Dead Time
• Charge-Pump and Bootstrap Maintain Upper Bias
Supplies
• DIS (Disable) Pin Pulls Gates Low
• Input Logic Thresholds Compatible with 5V to 15V
Logic Levels
• Very Low Power Consumption
• Undervoltage Protection
Chop Capability
• Bootstrap Supply Max Voltage to 95VDC
• Drives 1000pF Load at 1MHz in Free Air at +50oC with
Rise and Fall Times of Typically 10ns
• User-Programmable Dead Time
• Charge-Pump and Bootstrap Maintain Upper Bias
Supplies
• DIS (Disable) Pin Pulls Gates Low
• Input Logic Thresholds Compatible with 5V to 15V
Logic Levels
• Very Low Power Consumption
• Undervoltage Protection
HIP4080A Typical Application
• Medium/Large Voice Coil Motors
• Full Bridge Power Supplies
• Class D Audio Power Amplifiers
• High Performance Motor Controls
• Noise Cancellation Systems
• Battery Powered Vehicles
• Peripherals
• U.P.S.
• Full Bridge Power Supplies
• Class D Audio Power Amplifiers
• High Performance Motor Controls
• Noise Cancellation Systems
• Battery Powered Vehicles
• Peripherals
• U.P.S.
HIP4080A Connection Diagram
HIP4080A
PDF/DataSheet Download
- Datasheet: HIP4080A
- File Size: 204511 KB
- Manufacturer: INTERSIL [Intersil Corporation]
- Click here to Download
- ·HIP0045
- INTERSIL [Intersil Corporation]
- 1A/50V Octal Low Side Power Driver With Serial Bus Control and Fault Protection
- 95776 KB
- ·HIP0045AB
- INTERSIL [Intersil Corporation]
- 1A/50V Octal Low Side Power Driver With Serial Bus Control and Fault Protection
- 95776 KB
- ·HIP0050
- INTERSIL [Intersil Corporation]
- 0.3A/50V Octal Low Side Power Driver with Serial Bus Control and Over-Current Fault Flag
- 47084 KB
- ·HIP0050IB
- INTERSIL [Intersil Corporation]
- 0.3A/50V Octal Low Side Power Driver with Serial Bus Control and Over-Current Fault Flag
- 47084 KB
- ·HIP0051
- INTERSIL [Intersil Corporation]
- 0.25A/50V Octal Low Side Power Driver with Serial Bus Control
- 31796 KB
- ·HIP0051IB
- INTERSIL [Intersil Corporation]
- 0.25A/50V Octal Low Side Power Driver with Serial Bus Control
- 31796 KB
- ·HIP0060
- INTERSIL [Intersil Corporation]
- 1.5A, 50V Quad Low Side Power Driver with Serial Bus Control and Fault Protection
- 51353 KB
- ·HIP0060AB
- INTERSIL [Intersil Corporation]
- 1.5A, 50V Quad Low Side Power Driver with Serial Bus Control and Fault Protection
- 51353 KB
HIP4080A Relative Products
HIP4080
The HIP4080 is a high frequency, medium voltage Full Bridge N-Channel FET driver IC, available in 20 lead plastic SOIC and DIP packages. The HIP4080 includes an input comparator, used to facilitate the "hysteresis" and PWM modes of operation.Its HEN (high en...
HIP4020IBZT
IC DRIVER FULL-BRIDGE 20-SOIC
HIP4020IBZ
IC DRIVER FULL-BRIDGE 20-SOIC
HIP4020IB
In the Functional Block Diagram of the HIP4020, the four switches and a load are arranged in an H-Configuration so that the drive voltage from terminals OUTA and OUTB can be cross-switched to change the direction of current flow in the load. HIP4020, is comm...
HIP4020
In the Functional Block Diagram of the HIP4020, the four switches and a load are arranged in an H-Configuration so that the drive voltage from terminals OUTA and OUTB can be cross-switched to change the direction of current flow in the load. HIP4020 is commo...
HIP4011
The HIP4011 motor driver is intended for three phase Brushless motor control at continuous output currents up to 3A. It accepts inputs from buffered Hall effect sensors and drives three motor windings, regulating the current through an external current sensi...
Hotspot Suppliers Product
MC44BS373CAEFR2
Price: 1-1.5 USD
audio and video modulator, SOP, 6 V, 800 kHz, Channel 21–69 UHF operation, Boosted TVOUT level
K6T4008U1C-GF10
Price: 0.6-0.88 USD
512K x 8 bit, Low Power, Low Voltage, CMOS Static RAM, DIP/SOP, -0.5 to VCC+0.5 V
S3C44B0X01-ED80
Price: 4.5-5.2 USD
16/32-bit, RISC microprocessor, QFP160 pins, ± 200 mA, Total 8 memory banks
DCR010505U
Price: 14-18 USD
IC ISOLATED 5V 0.2A 12SOP - DCR010505U
AM27C010-90DC
Price: 0.5-2 USD
1 Megabit, ultraviolet erasable programmable read-only memory, DIP
4N33-X009T
Price: 0.1-100 USD
SMD, optically coupled isolator, Lead-free component, 10Ω, Integrated Circuits, Vishay Siliconix
PP30012HS
Price: 1111-1397 USD
PP30012HS, The ABB Group, Semiconductor Modules, Square RBSOA, Low Saturation Voltage
EPM3032ATC44-10N
Price: 1.1-1.15 USD
low–cost, high–performance device, QFP44, –2.0 to 5.75 V, CMOS EEPROM, 227.3 MHz
K4D263238K-VC40
Price: 2.45-2.55 USD
128M, 1M x 32Bit x 4 Banks, 250MHz, GDDR SDRAM
TLV2772CDGK
Price: 0.001-1 USD
operational amplifier, 7V, SOP
ADG609BNZ
Price: 1.3-1.8 USD
DIP16，ADG609BNZ, 3 V/5 V, 4/8 Channel, Analog Multiplexer, +0.3 V to –6.5 V
PS11035-1
Price: 22-39 USD
intelligent power module, 450V, Inverter output current capability IO
