Purchase MX29LV800BT, In-stock MX29LV800BT From SeekIC.
Part Number: MX29LV800BT
Description: The MX29LV800BT/BB is a 8-mega bit Flash memory organized as 1M bytes of 8 bits or 512K words of 16 bi...
- Table of contents:
MX29LV800BT
-
Suppliers
DataSheet
General Description
MX29LV800BT General Description
The MX29LV800BT/BB is a 8-mega bit Flash memory organized as 1M bytes of 8 bits or 512K words of 16 bits. MXIC's Flash memories offer the most cost-effective and reliable read/write non-volatile random access memory. The MX29LV800BT/BB is packaged in 44-pin SOP, 48-pin TSOP, and 48-ball CSP. It is designed to be reprogrammed and erased in system or in standard EPROM programmers.
The standard MX29LV800BT/BB offers access time as fast as 70ns, allowing operation of high-speed microprocessors without wait states. To eliminate bus contention, the MX29LV800BT/BB has separate chip enable (CE#) and output enable (OE#) controls.
MXIC's Flash memories augment EPROM functionality with in-circuit electrical erasure and programming. The MX29LV800BT/BB uses a command register to manage this functionality. The command register allows for 100% TTL level control inputs and fixed power supply levels during erase and programming, while maintaining maximum EPROM compatibility.
MXIC Flash technology reliably stores memory contents even after 100,000 erase and program cycles. The MXIC cell is designed to optimize the erase and programming mechanisms. In addition, the combination of advanced tunnel oxide processing and low internal electric fields for erase and program operations produces reliable cycling.
The MX29LV800BT/BB uses a 2.7V~3.6V VCC supply to perform the High Reliability Erase and auto Program/Erase algorithms.
The highest degree of latch-up protection is achieved with MXIC's proprietary non-epi process. Latch-up protection is proved for stresses up to 100 milliamperes on address and data pin from -1V to VCC + 1V.
MX29LV800BT Maximum Ratings
Storage Temperature
Plastic Packages . . . . . . . . . . . . . ..... -65 to +150
Ambient Temperature
with Power Applied. . . . . . . . . . . . . .... -65 to +125
Voltage with Respect to Ground
VCC (Note 1) . . . . . . . . . . . . . . . . . -0.5 V to +4.0 V
A9, OE#, and
RESET# (Note 2) . . . . . . . . . . . ....-0.5 V to +12.5 V
All other pins (Note 1) . . . . . . . -0.5 V to VCC +0.5 V
Output Short Circuit Current (Note 3) . . . . . . 200 mA
Notes:
1. Minimum DC voltage on input or I/O pins is -0.5 V.
During voltage transitions, input or I/O pins may overshoot VSS to -2.0 V for periods of up to 20 ns. See Figure 6. Maximum DC voltage on input or I/O pins is
VCC +0.5 V. During voltage transitions, input or I/O pins may overshoot to VCC +2.0 V for periods up to 20 ns.
2. Minimum DC input voltage on pins A9, OE#, and RESET# is -0.5 V. During voltage transitions, A9, OE#, and RESET# may overshoot VSS to -2.0 V for periods of up to 20 ns. See Figure 6. Maximum DC input voltage on pin A9 is +12.5 V which may overshoot to 14.0 V for periods up to 20 ns.
3. No more than one output may be shorted to ground at a time. Duration of the short circuit should not be greater than one second.
Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device.
This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational sections of this data sheet is not implied. Exposure of the device to absolute maximum rating conditions for extended periods may affect device reliability.
Plastic Packages . . . . . . . . . . . . . ..... -65 to +150
Ambient Temperature
with Power Applied. . . . . . . . . . . . . .... -65 to +125
Voltage with Respect to Ground
VCC (Note 1) . . . . . . . . . . . . . . . . . -0.5 V to +4.0 V
A9, OE#, and
RESET# (Note 2) . . . . . . . . . . . ....-0.5 V to +12.5 V
All other pins (Note 1) . . . . . . . -0.5 V to VCC +0.5 V
Output Short Circuit Current (Note 3) . . . . . . 200 mA
Notes:
1. Minimum DC voltage on input or I/O pins is -0.5 V.
During voltage transitions, input or I/O pins may overshoot VSS to -2.0 V for periods of up to 20 ns. See Figure 6. Maximum DC voltage on input or I/O pins is
VCC +0.5 V. During voltage transitions, input or I/O pins may overshoot to VCC +2.0 V for periods up to 20 ns.
2. Minimum DC input voltage on pins A9, OE#, and RESET# is -0.5 V. During voltage transitions, A9, OE#, and RESET# may overshoot VSS to -2.0 V for periods of up to 20 ns. See Figure 6. Maximum DC input voltage on pin A9 is +12.5 V which may overshoot to 14.0 V for periods up to 20 ns.
3. No more than one output may be shorted to ground at a time. Duration of the short circuit should not be greater than one second.
Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device.
This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational sections of this data sheet is not implied. Exposure of the device to absolute maximum rating conditions for extended periods may affect device reliability.
MX29LV800BT Features
• Extended single - supply voltage range 2.7V to 3.6V
• 1,048,576 x 8/524,288 x 16 switchable
• Single power supply operation
- 3.0V only operation for read, erase and program
operation
• Fast access time: 70/90ns
• Low power consumption
- 20mA maximum active current
- 0.2uA typical standby current
• Command register architecture
- Byte/word Programming (9us/11us typical)
- Sector Erase (Sector structure 16K-Bytex1,
8K-Bytex2, 32K-Bytex1, and 64K-Byte x15)
• Fully compatible with MX29LV800T/B device
• Auto Erase (chip & sector) and Auto Program
- Automatically erase any combination of sectors with
Erase Suspend capability.
- Automatically program and verify data at specified
address
• Erase suspend/Erase Resume
- Suspends sector erase operation to read data from,
or program data to, any sector that is not being erased,
then resumes the erase.
• Status Reply
- Data# polling & Toggle bit for detection of program
and erase operation completion.
• Ready/Busy# pin (RY/BY#)
- Provides a hardware method of detecting program or
erase operation completion.
• Sector protection
- Hardware method to disable any combination of
sectors from program or erase operations
- Temporary sector unprotected allows code changes
in previously locked sectors.
• CFI (Common Flash Interface) compliant
- Flash device parameters stored on the device and
provide the host system to access
• 100,000 minimum erase/program cycles
• Latch-up protected to 100mA from -1V to VCC+1V
• Boot Sector Architecture
- T = Top Boot Sector
- B = Bottom Boot Sector
• Package type:
- 44-pin SOP
- 48-pin TSOP
- 48-pin CSP
• Compatibility with JEDEC standard
- Pinout and software compatible with single-power
supply Flash
• 10 years data retention
• 1,048,576 x 8/524,288 x 16 switchable
• Single power supply operation
- 3.0V only operation for read, erase and program
operation
• Fast access time: 70/90ns
• Low power consumption
- 20mA maximum active current
- 0.2uA typical standby current
• Command register architecture
- Byte/word Programming (9us/11us typical)
- Sector Erase (Sector structure 16K-Bytex1,
8K-Bytex2, 32K-Bytex1, and 64K-Byte x15)
• Fully compatible with MX29LV800T/B device
• Auto Erase (chip & sector) and Auto Program
- Automatically erase any combination of sectors with
Erase Suspend capability.
- Automatically program and verify data at specified
address
• Erase suspend/Erase Resume
- Suspends sector erase operation to read data from,
or program data to, any sector that is not being erased,
then resumes the erase.
• Status Reply
- Data# polling & Toggle bit for detection of program
and erase operation completion.
• Ready/Busy# pin (RY/BY#)
- Provides a hardware method of detecting program or
erase operation completion.
• Sector protection
- Hardware method to disable any combination of
sectors from program or erase operations
- Temporary sector unprotected allows code changes
in previously locked sectors.
• CFI (Common Flash Interface) compliant
- Flash device parameters stored on the device and
provide the host system to access
• 100,000 minimum erase/program cycles
• Latch-up protected to 100mA from -1V to VCC+1V
• Boot Sector Architecture
- T = Top Boot Sector
- B = Bottom Boot Sector
• Package type:
- 44-pin SOP
- 48-pin TSOP
- 48-pin CSP
• Compatibility with JEDEC standard
- Pinout and software compatible with single-power
supply Flash
• 10 years data retention
MX29LV800BT Connection Diagram
MX29LV800BTC-70
PDF/DataSheet Download
- Datasheet: MX29LV800BTC-70
- File Size: 1276593 KB
- Manufacturer: MCNIX [Macronix International]
- Click here to Download
- ·MX205Q
- ETC [ETC]
- Low Cost, 5.0g, Dual Axis Accelerometer with Analog Outputs
- 252911 KB
- ·MX205QC
- ETC [ETC]
- Low Cost, 5.0g, Dual Axis Accelerometer with Analog Outputs
- 252911 KB
- ·MX205QL
- ETC [ETC]
- Low Cost, 5.0g, Dual Axis Accelerometer with Analog Outputs
- 252911 KB
- ·MX210Q
- ETC [ETC]
- Low Cost, 10g, Dual Axis Accelerometer with Analog Outputs
- 252922 KB
- ·MX210QC
- ETC [ETC]
- Low Cost, 10g, Dual Axis Accelerometer with Analog Outputs
- 252922 KB
- ·MX210QL
- ETC [ETC]
- Low Cost, 10g, Dual Axis Accelerometer with Analog Outputs
- 252922 KB
- ·MX214
- CMLMICRO [CML Microcircuits]
- Variable Split Band Inverter
- 238010 KB
- ·MX23C1010
- MCNIX [Macronix International]
- 1M-BIT MASK ROM (8 BIT OUTPUT)
- 119262 KB
MX29LV800BT Relative Products
MX29LV800BB
The MX29LV800BT/MX29LV800BB is a 8-mega bit Flash memory organized as 1M bytes of 8 bits or 512K words of 16 bits. MXIC's Flash memories offer the most cost-effective and reliable read/write non-volatile random access memory. The MX29LV800BT/BB is packaged i...
MX29LV800B
The MX29LV800T/MX29LV800B is a 8-mega bit Flash memory organized as 1M bytes of 8 bits or 512K words of 16 bits.MXIC's Flash memories offer the most cost-effective and reliable read/write non-volatile random access memory. The MX29LV800T/B is packaged in 44-...
MX29LV640T
The MX29LV640T/B is a 64-mega bit Flash memory organized as 8M bytes of 8 bits or 4M bytes of 16 bits. MXIC's Flash memories offer the most cost-effective and reliable read/write non-volatile random access memory. The MX29LV640T/B is packaged in 48-pin TSOP,...
MX29LV640EBTI-70G
The MX29LV640EBTI-70G is designed as one kind of 8-mega bit flash memory device that offers access time as fast as 45ns, allowing operation of high-speed microprocessors without wait states. And this device uses a 2.7V to 3.6V VCC supply to perform the High ...
MX29LV640E T/B
MX29LV640DT
Hotspot Suppliers Product
ADS1230IPWR
Price: 0.75-0.85 USD
20-bit analog-to-digital converter, SOP-16PIN, 2.7V to 5.3V, Onboard Oscillator
CF775-04SO
Price: 2.8-3.2 USD
CF775-04SO SOP28 Microchip Technology
74HC175D
Price: 0.1-0.2 USD
high-speed, Si-gate CMOS device, SOP16
XC9572-10TQG100C
Price: 1.89-2.1 USD
high-performance CPLD, 72 Macrocells, 10ns, 100TQFP, 72 I/O, In System Programmable
L6235D013TR
Price: 4-4.5 USD
IC DRIVER 3PHASE DC MOTOR 24SOIC - L6235D013TR
AT25F1024AN-10SU-2.7
Price: 0.1-1 USD
1Mbit, High Speed SPI Serial Flash Memory, 33 MHz Clock Rate, Low-voltage Operation, SOP8
ML6652EH
Price: 4-6 USD
Media Converter, QFP-48, 3.3V, 10Mbps, 100Mbps, Serial Management Interface, PMD modules
ADS831E
Price: 5-5.5 USD
pipeline, CMOS analog-to-digital converter, SSOP20, +6V, high SNR, differential analog input, low ...
EKMM221VSN181MQ20S
Price: 0.01-100 USD
large capacitance, aluminum electrolytic capacitor, 160 to 400V, Non solvent-proof type, 180uF
ISD2548P
Price: 8-12 USD
record/playback device, DIP-28, (VSS –0.3V) to (VCC +0.3V)
74HCT688D
Price: 0.1-1 USD
8-bit magnitude comparator, SOP, 7A
PIC16F54-I/P
Price: 0.32-0.42 USD
Flash-Based, 8-Bit CMOS Microcontroller
