TLE6232GP

On Time (Max) :
Off Time (Max) :
Operating Supply Voltage :
Mounting Style : SMD/SMT
Maximum Operating Temperature : + 150 C
Package / Case : DSO-38
On Resistance (Max) : 0.25 Ohms
Number of Outputs : 6
Supply Current (Max) : 10 mA


Features:

• Short Circuit Protection up to 24 V
• Over-temperature Protection
• Over-voltage Protection
• 16 bit Serial Data Input and Diagnostic Output (2 bit/ch. acc. SPI protocol)
• Direct Parallel Control of all six Channels for PWM Applications
• General Fault Flag
• Low Quiescent Current
• Compatible with 3V Micro Controllers
• Electrostatic Discharge (ESD) Protection
• Parallel Inputs High or Low Active Programmable




Application

• µC Compatible Power Switch for 12 V and 24V Applications
• Switch for Automotive and Industrial System
• Solenoids, Relays and Resistive Loads
• Robotic Controls




Pinout








Specifications

Parameter	Symbol	Values	Unit
Supply Voltage	VS	-0.3 ... +7	V
Continuous Drain Source Voltage (OUT1...OUT8)	VDS	45	V
Input Voltage, All Inputs and Data Lines	VIN	- 0.3 ... + 7	V
Operating Temperature Range Storage Temperature Range	Tj Tstg	- 40 ... + 150 - 55 ... + 150	°C
Output Current per Channel (see el. characteristics)	ID(lim)	ID(lim) min	A
Single pulse inductive Energy (internal clamping) Tj=125°C, Ch1-4: 3A linear decreasing Ch5,6: 1,5A linear decreasing	E	40 20
Output Current per Channel @ TA = 25°C (All 6 Channels ON; Mounted on PCB ) 1)	ID 1-4 ID 5,6	1.1 0.55	mJ
Power Dissipation (mounted on PCB) @ TA = 25°C	Ptot	3.3	A
Electrostatic Discharge Voltage (Human Body Model) according to MIL STD 883D, method 3015.7 and EOS/ESD assn. standard S5.1 - 1993	VESD	2000	W
DIN Humidity Category, DIN 40 040		E	V
IEC Climatic Category, DIN IEC 68-1		40/150/56
Thermal Resistance junction case (die soldered on the frame) junction - ambient @ min. footprint junction - ambient @ 6 cm2 cooling area with heat pipes	RthJC RthJA	2 50 38	K/W

Description

Six Channel Low-Side Switch in Smart Power Technology (SPT) with a Serial Peripheral Interface (SPI) and six open drain DMOS output stages. The TLE6232GP is protected by embedded protection functions and designed for automotive and industrial applications. The output stages are controlled via an SPI Interface. Additionally all six channels can be controlled direct in parallel for PWM applications. Therefore the TLE 6232 GP is particularly suitable for engine management and powertrain systems.

The TLE6232GP is protected by embedded protection functions and designed for automotive and industrial applications. The output stages are controlled via an SPI Interface.Additionally all six channels can be controlled direct in parallel for PWM applications. Therefore the TLE6232GP is particularly suitable for engine management and powertrain systems.

Features of the TLE6232GP are:(1)short circuit protection up to 24 V;(2)16 bit serial data input and diagnostic output (2 bit/ch. acc. SPI protocol);(3)direct parallel control of all six channels for PWM applications;(4)compatible with 3V micro controllers;(5)electrostatic discharge (ESD) protection;(6)parallel inputs high or low active programmable.The serial SPI interface makes possible communication between TLE6232 and the microcontroller.TLE6232GP always works in slave mode whereas the microcontroller provides the master function. The maximum baud rate is 5MBaud.

The absolute maximum ratings of the TLE6232GP can be summarized as:(1)continuous drain source voltage (OUT1...OUT8) Vds:45V;(2)input voltage, all inputs and data lines Vin:-0.3 to +7V;(3)supply voltage Vs:-0.3 to +7 V;(4)power dissipation (mounted on PCB) @ TA = 25°C Ptot:3.3W.In order to increase the possible number of SPI participants on one and the same CS signal,bits 7 and 6 of the instruction byte are fixed as shown above. While receiving the first two bits of the instruction byte the data output SO has to be in tri-state. After having received the first two bits TLE6232 has to decide if it is addressed (bit 7 = high, bit 6 = low). In this case the remaining 6 bits of the instruction byte and the data byte are accepted and the diagnostic feed-back respectively the data byte content (MUX, SCON) is sent to the microcontroller. Otherwise instruction and data bits are rejected and SO remains in tri-state. Infineon Technologies Components may only be used in life-support devices or systems with the express written approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure of that life-support device or system, or to affect the safety or effectiveness of that device or system of  the TLE6232GP. Life support devices or systems are intended to be implanted in the human body, or to support and/or maintain and sustain and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may be endangered.

Parameters:

Technical/Catalog Information	TLE6232GP
Vendor	Infineon Technologies
Category	Integrated Circuits (ICs)
Package / Case	DSO-36
Mounting Type	Surface Mount
Type	Low Side
Voltage - Supply	4.5 V ~ 5.5 V
On-State Resistance	250 mOhm
Current - Output/Channel	1.1A
Current - Peak Output	4A
Packaging	-
Input Type	SPI
Number of Outputs	6
Operating Temperature	-40°C ~ 150°C
Lead Free Status	Lead Free
RoHS Status	RoHS Compliant
Other Names	TLE6232GP TLE6232GP