© 2008-2012 SeekIC.com Corp.All Rights Reserved.
Response in 12 hours
Vendor:Other Category:Other
These DM74185A monolithic converters are derived from the 256-bit read only memories, DM5488, and DM7488. Emitter connections are made to provide direct read-out of converted codes at outputs Y8 through Y1, as shown in...
Vendor:Other Category:Other
These DM74184 monolithic converters are derived from the 256-bit read only memories, DM5488, and DM7488. Emitter connections are made to provide direct read-out of converted codes at outputs Y8 through Y1, as shown in ...
Vendor:Other Category:Other
These universal 9-bit (8 data bits plus 1 parity bit) parity generatorscheckers DM74180 feature oddeven outputs and control inputs to facilitate operation in either odd or even parity ap- plications Depending on whethe...
Vendor:Other Category:Other
These DM74175 positive-edge triggered flip-flops utilize TTL circuitry to implement D-type flip-flop logic. All DM74175 have a direct clear input, and the quad (175) version features complementary outputs from each fli...
Mfg:TOSHIBA Pack:SOP D/C:41 Vendor:Other Category:Other
These DM74174 positive-edge triggered flip-flops utilize TTL circuitry to implement D-type flip-flop logic. All have a direct clear input, and the quad (175) version features complementary outputs from each flip-flop. ...
Vendor:Other Category:Other
These DM74173 four-bit registers contain D-type flip-flops with totempole TRI-STATE outputs, capable of driving highly capacitive or low-impedance loads. The high-impedance state and increased high-logic-level drive pr...
D/C:N/A Vendor:Other Category:Other
This DM7417 device contains six independent gates each of which performs a buffer function The open-collector outputs re-quire external pull-up resistors for proper logical operation
Vendor:Other Category:Other
The DM74165 is an 8-bit parallel load or serial-in register with complementary outputs available from the last stage. Parallel inputting occurs asynchronously when the Parallel Load (PL) input is LOW. With PL HIGH, ser...
Vendor:Other Category:Other
These DM74164 8-bit shift registers feature gated serial inputs and an asynchronous clear. A LOW logic level at either serial input inhibits entry of the new data, and resets the first flip-flop to the LOW level at the...
Vendor:Other Category:Other
These DM74161 synchronous presettable counters feature an inter-nal carry look-ahead for application in high-speed counting designs The DM74161 and DM74163 are 4-bit binary counters The carry output is decoded by m...
Vendor:Other Category:Other
These DM74161 synchronous presettable counters feature an inter-nal carry look-ahead for application in high-speed counting designs The DM74161 and DM74163 are 4-bit binary counters The carry output is decoded by me...
Mfg:NS Pack:DIP Vendor:Other Category:Other
This DM7416 contains six independent gates each of which performs the logic INVERT function. The open-collector outputs require external pull-up resistors for proper logical operation.
Vendor:Other Category:Other
These DM74157 data selectors/multiplexers contain inverters and drivers to supply full on-chip data selection to the four outputgates. A separate strobe input is provided. A 4-bit word is selected from one of two sourc...
Vendor:Other Category:Other
These DM74155 TTL circuits feature dual 1-line-to-4-line demultiplexers with individual strobes and common binary-address inputs in a single 16-pin package. When both sections are enabled by the strobes, the common add...
Vendor:Other Category:Other
Each or these DM74154 4-line-to-16-line decoders utilizes TTL circuitry to decode four binary-coded inputs into one of sixteen mutually exclusive outputs when both the strobe inputs, G1 and G2, are low. The demultiplexin...
Mfg:NS Pack:9030 D/C:DIP16 Vendor:Other Category:Other
Each of these DM74153 data selectors/multiplexers contains inverters and drivers to supply fully complementary, on-chip, binary decoding data selection to the AND-OR-invert gates. Separate strobe inputs are provided fo...
Vendor:Other Category:Other
These DM74151A data selectors/multiplexers contain full on-chip decoding to select the desired data source. The DM74150 selects one-of-sixteen data sources; the DM74151A selects one-of-eight data sources. The DM74150 and...
Vendor:Other Category:Other
The DM74150N is designed as one kind of data selectors/multiplexers which contains full on-chip decoding to select the desired data source. DM74150N has a strobe input which must be at a low logic level to enable these d...
Mfg:NS D/C:08+ Vendor:Other Category:Other
These DM74150 data selectors/multiplexers contain full on-chip decoding to select the desired data source. The DM74150 selects one-of-sixteen data sources; the DM74151A selects one-of-eight data sources. The DM74150 and ...
Vendor:Other Category:Other
These DM74145 BCD-to-decimal decoders/drivers consist of eight inverters and ten, four-input NAND gates. The invertersof DM74145 are connected in pairs to make BCD input data available for decoding by the NAND gates. ...
Vendor:Other Category:Other
This DM7414 device contains six independent gates each of which Performs the logic INVERT function Each input has hyster-esis which increases the noise immunity and transforms a Slowly changing input signal to a fast ch...
Vendor:Other Category:Other
This DM74132 contains four independent gates each of which performs the logic NAND function Each input has hystere-sis which increases the noise immunity and transforms a slowly changing input signal to a fast changing...
Vendor:Other Category:Other
This DM74125 contains four independent gates each of which performs a non-inverting buffer function The outputs of DM74125 have the TRI-STATE feature When enabled the outputs exhibit the low impedance characteristics of ...
Mfg:NS Pack:89+ D/C:975
Vendor:Other Category:Other
The DM74123 is a dual retriggerable monostable multivibrator capable of generating output pulses from a few nano-seconds to extremely long duration up to 100% duty cycle. Each DM74122 device has three inputs permittin...
Vendor:Other Category:Other
The DM74122 features positive and negative DC level triggering nputs, complementary outputs, an optional 10 kX internal timing resistor and an overriding Direct Clear (CD) input.When the DM74122 circuit is in the quasi-s...
Vendor:Other Category:Other
The DM54121/DM74121 is a monostable multivibrator featuring both positive and negative edge triggering with complementary outputs. An internal 2kX timing resistor is provided for design convenience minimizing component...
Vendor:Other Category:Other
This DM7410 contains three independent gates each of which performs the logic NAND function.
Vendor:Other Category:Other
This DM7409 contains four independent gates each of which performs the logic AND function The open-collector outputs require external pull-up resistors for proper logical operation
D/C:N/A Vendor:Other Category:Other
This DM7408 contains four independent gates each of which performs the logic AND function
Mfg:N/A Pack:NA/ D/C:09+ Vendor:Other Category:Other
This DM7407 contains six independent gates each of which performs a buffer function. The open-collector outputs require external pull-up resistors for proper logical operation.
Mfg:NS D/C:SOP3.9 Vendor:Other Category:Other
This DM7406 contains six independent buffers each of which performs the logic INVERT function The open-collector out-puts require external pull-up resistors for proper logical op-eration
Vendor:Other Category:Other
This DM7405 contains six independent gates each of which performs the logic INVERT function The open-collector out- puts require external pull-up resistors for proper logical op-eration
Vendor:Other Category:Other
This DM7404 contains six independent gates each of which performs the logic INVERT function
Vendor:Other Category:Other
This DM7403 contains four independent gates each of which performs the logic NAND function. The open-collector outputs require external pull-up resistors for proper logical operation.
Vendor:Other Category:Other
This DM7402 contains four independent gates each of which performs the logic NOR function
Vendor:Other Category:Other
This DM7401 contains four independent gates each of which Performs the logic NAND function The open-collector out-puts require external pull-up resistors for proper logical op-eration
Vendor:Other Category:Other
This DM7400 contains four independent gates each of which performs the logic NAND function.
Vendor:Other Category:Other
This DM7160 offers comparisons to determine equality be-tween two binary words The DM7160 compares two six-bit words A strobe override is provided When the strobe is taken to a high logic level the output is forced to ...
Vendor:Other Category:Other
The DM7136 is designed as one kind of 6-bit unified bus comparator with open-collector outputs. DM7136 compares two binary words of two-to-six bits in length and indicates matching (bit-for-bit) of the two words.DM7136 h...
Vendor:Other Category:Other
This DM64ALS08 contains four independent gates each of which performs the logic AND functionThe DM64ALS08 version features the same performance as the standard version DM74ALS08 with a guarantee over an extended temperat...
Vendor:Other Category:Other
The DM562P integrated modem is a two-chipset design that provides a complete solution for state-of-the-art, voice-band Plain Old Telephone Switching (POTS) communication. The modem provides for Data (up to 56,000bps),Fax...
Vendor:Other Category:Other
The DM562AP integrated modem is a two-chipset design that provides a complete solution for state-of-the-art, voice-band Plain Old Telephone Switching (POTS) communication. The modem provides for Data (up to 56,000bps), F...
Vendor:Other Category:Other
The DM560P integrated modem is a four chipset design that provides a complete solution for state-of-the-art, voice-band Plain Old Telephone Service(POTS) communication. The modem provides for Data (up to 56,000bps), Fax ...
Vendor:Other Category:Other
The DM54S472 is organized in the popular 512 words by 8 bits configuration. A memory enable inputs is provided to control the output states. The features of the DM54S472 are: (1)advanced titanium-tungsten fuses; (2)schot...
Vendor:Other Category:Other
The DM54S287 is organized in the popular 256 words by 4 bits configuration. The feature of DM54S287 are as follows: (1)advanced titanium-tungsten fuses; (2)schottky-clamped for speed; (3)PNP inputs for reduced input load...
Vendor:Other Category:Other
These DM54S194 bidirectional shift registers are designed to incorporate virtually all of the features a system designer may want in a shift register; they feature parallel inputs, parallel outputs, right-shift and left-...
Vendor:Other Category:Other
These DM54LS85 4-bit magnitude comparators perform comparison of straight binary or BCD codes. Three fully-decoded decisions about two, 4-bit words (A, B) are made and are externally available at three outputs. These ...
Vendor:Other Category:Other
DM54LS74A contains two independent positive-edge-triggered D flip-flops with complementary outputs. The informa-tion on the D input is accepted by the flip-flops on the positive going edge of the clock pulse. The trigg...
Vendor:Other Category:Other
This DM54LS55 contains a combination of AND-OR-INVERT functions. The internal gates are configured as two, four-input AND gates with their outputs connected to a two-input NOR gate.
Vendor:Other Category:Other
The DM54LS502 is an 8-bit register with the interstage logic necessary to perform serial-to-parallel conversion and provide an active LOW Conversion Complete (CC) signal coincident with storage of the eighth bit. An acti...
Vendor:Other Category:Other
The DM54LS469 is an 8-bit synchronous up/down counter with parallel load and hold capability. Three function-select in-puts (LD,UD, CBI) provide one of four operations which occur synchronously on the rising edge of the...
Vendor:Other Category:Other
The DM54LS461 is an 8-bit synchronous counter with parallel load, clear, and hold capability. Two function select inputs (I0, I1) provide one of four operations which occur synchronously on the rising edge of the clock (...
Vendor:Other Category:Other
These DM54LS42 BCD-to-decimal decoders consist of eight inverters and ten four-input NAND gates The inverters are connect-ed in pairs to make DM54LS42 BCD input data available for decoding by the NAND gates Full decoding...
Vendor:Other Category:Other
The DM54LS377 is an 8-bit register built using advanced low power Schottky technology. This register consists of eight D-type flip-flops with a buffered common clock and a buffered common input enable. The device is pack...
Vendor:Other Category:Other
These DM54LS374 8-bit registers feature totem-pole TRI-STATE outputs designed specifically for driving highly-capacitive or relatively low-impedance loads. The high-impedance state and increased high-logic level drive pr...
Vendor:Other Category:Other
These DM54LS373 8-bit registers feature totem-pole TRI-STATE outputs designed specifically for driving highly-capacitive or relatively low-impedance loads. The high-impedance state and increased high-logic level drive pr...
Vendor:Other Category:Other
This DM54LS368A device contains six independent gates each of which performs an inverting buffer function. The outputs have the TRI-STATE feature. When enabled, the outputs of DM54LS368A exhibit the low impedance charact...
Mfg:N/A Pack:N/A D/C:N/A Vendor:Other Category:Other
This DM54LS365A device contains six independent gates each of which performs a non-inverting buffer function. The outputs of DM54LS365A have the TRI-STATE feature. When enabled, the outputs of DM54LS365A exhibit the low ...
Vendor:Other Category:Other
The DM54LS323 is an 8-bit universal shift/storage register with TRI-STATEÉ outputs. The function of DM54LS323 is similar to the 'LS299 with the exception of Synchronous Reset. Parallel load in-puts and flip-flop ...
Vendor:Other Category:Other
This DM54LS32 device contains four independent gates each of which performs the logic OR function
Vendor:Other Category:Other
The DM54LS299 is an 8-bit universal shift/storage register with TRI-STATE. outputs. Four modes of operation are possible: hold (store), shift left, shift right and load data. The parallel load inputs and flip-flop output...
Vendor:Other Category:Other
These DM54LS283 full adders perform the addition of two 4-bit binary numbers. The sum (R) outputs are provided for each bit and the resultant carry (C4) is obtained from the fourth bit. These DM54LS283 adders feature ...
Vendor:Other Category:Other
The DM54LS279 consists of four individual and independent Set- Reset Latches with active low inputs Two of the four latch- es have an additonal S input ANDed with the primary S input A low on any S input while the R inpu...
Vendor:Other Category:Other
The DM54LS273 is a high speed 8-bit register, consisting of eight D-type flip-flops with a common Clock and an asynchronous active LOW Master Reset. This DM54LS273 device is supplied in a 20-pin package featuring 0.3 ...
Vendor:Other Category:Other
This DM54LS260 device contains two individual five input gates, each of which perform the logic NOR function.
Vendor:Other Category:Other
These DM54LS258B Schottky-clamped high-performance multiplexers feature TRI-STATE outputs that can interface directly with data lines of bus-organized systems.With all but one of the common outputs of DM54LS258B disabled...
Vendor:Other Category:Other
These DM54LS257B Schottky-clamped high-performance multiplexers feature TRI-STATE outputs that can interface directly with data lines of bus-organized systems.With all but one of the common outputs of DM54LS257B disabled...
Vendor:Other Category:Other
Each of these DM54LS253 Schottky-clamped data selectors/multiplexers contains inverters and drivers to supply fully complementary,on-chip, binary decoding data selection to the AND-OR gates. Separate output control input...
Vendor:Other Category:Other
These DM54LS245 octal bus transceivers are designed for asynchro- nous two-way communication between data buses Thecontrol function implementation minimizes external timing requirementsThe DM54LS245 device allows data tr...
Vendor:Other Category:Other
These DM54LS241 buffersline drivers are designed to improve both the performance and PC board density of TRI-STATE buffers drivers employed as memory-address drivers clock drivers and bus-oriented transmittersreceivers F...
Vendor:Other Category:Other
These DM54LS240 buffersline drivers are designed to improve both the performance and PC board density of TRI-STATE buffers drivers employed as memory-address drivers clock drivers and bus-oriented transmittersreceivers F...
Vendor:Other Category:Other
This DM54LS21 device contains two independent gates each of which performs the logic AND function
Vendor:Other Category:Other
These DM54LS191 circuits are synchronous reversible updown coun-ters The DM54LS191 is a 4-bit binary counter and the DM54LS190 is a BCD counter ynchronous operation is provided by having all flip-flops clocked simultaneo...
Vendor:Other Category:Other
These DM54LS190 circuits are synchronous reversible updown coun-ters The DM54LS191 is a 4-bit binary counter and the DM54LS190 is a BCD counter ynchronous operation is provided by having all flip-flops clocked simultaneo...
Vendor:Other Category:Other
The DM54LS181 is a 4-bit Arithmetic Logic Unit (ALU) which can perform all the possible 16 logic operations on two variables and a variety of arithmetic operations
Mfg:CDIP Pack:N\A D/C:N\A Vendor:Other Category:Other
These DM54LS175 positive-edge-triggered flip-flops utilize TTL circuitry to implement D-type flip-flop logic. All DM54LS175 have a direct clear input, and the quad (175) versions feature complementary outputs from e...
Vendor:Other Category:Other
These DM54LS174 positive-edge-triggered flip-flops utilize TTL circuitry to implement D-type flip-flop logic. All DM54LS174 have a direct clear input, and the quad (175) versions feature complementary outputs from ea...
Vendor:Other Category:Other
This DM54LS165 device is an 8-bit serial shif tregister which shifts data in the direction of QA toward QH when clocked Parallel-in ac-cess is made available by eight individual direct data inputs which are enabled by ...
Vendor:Other Category:Other
These DM54LS164 8-bit shift registers feature gated serial inputs and an asynchronous clear. A low logic level at either input inhibits entry of the new data, and resets the first flip-flop to the low level at the ne...
Vendor:Other Category:Other
These DM54LS163A synchronous, presettable counters feature an internal carry look-ahead for application in high-speed counting designs. The DM54LS163A and DM54LS161A are 4-bit binary counters. The carry output is decoded...
Vendor:Other Category:Other
These DM54LS161A synchronous, presettable counters feature an internal carry look-ahead for application in high-speed counting designs. The DM54LS161A and DM54LS163A are 4-bit binary counters. The carry output is decoded...
Vendor:Other Category:Other
These DM54LS158 data selectors/multiplexers contain inverters and drivers to supply full on-chip data selection to the four output gates. A separate strobe input is provided. A 4-bit word is selected from one of two sour...
Vendor:Other Category:Other
These DM54LS157 data selectors/multiplexers contain inverters and drivers to supply full on-chip data selection to the four output gates. A separate strobe input is provided. A 4-bit word is selected from one of two sour...
Vendor:Other Category:Other
These DM54LS156 TTL circuits feature dual 1-line-to-4-line demultiplexers with individual strobes and common binary-address inputs in a single 16-pin package. When both sections are enabled by the strobes, the common add...
Vendor:Other Category:Other
These DM54LS155 TTL circuits feature dual 1-line-to-4-line demultiplexers with individual strobes and common binary-address inputs in a single 16-pin package. When both sections are enabled by the strobes, the common add...
Vendor:Other Category:Other
Each of these DM54LS154 4-line-to-16-line decoders utilizes TTL circuit-ry to decode four binary-coded inputs into one of sixteen mutually exclusive outputs when both the strobe inputs G1 and G2 are low. The demultiple...
Vendor:Other Category:Other
Each of these DM54LS153 data selectors/multiplexers contains inverters and drivers to supply fully complementary, on-chip, binary decoding data selection to the AND-OR-invert gates. Separate strobe inputs are provided fo...
Vendor:Other Category:Other
This DM54LS151 data selector/multiplexer contains full on-chip decoding to select the desired data source. The DM54LS151 selects one-of-eight data sources. The DM54LS151 has a strobe input which must be at a low logic le...
Vendor:Other Category:Other
These DM54LS139 Schottky-clamped circuits are designed to be used in high-performance memory-decoding or data-routing applications, requiring very short propagation delay times. In high-performance memory systems these D...
Vendor:Other Category:Other
These DM54LS138 Schottky-clamped circuits are designed to be used in high-performance memory-decoding or data-routing applications, requiring very short propagation delay times. In high-performance memory systems these D...
Vendor:Other Category:Other
This DM54LS125A device contains four independent gates each of which performs a non-inverting buffer function. The outputsof DM54LS125A have the TRI-STATE feature. When enabled, the outputs of DM54LS125A exhibit the low ...
Vendor:Other Category:Other
This DM54LS11 device contains three independent gates each of which performs the logic AND function.
Vendor:Other Category:Other
This DM54LS109A device contains two independent positive-edge-triggered J-K flip-flops with complementary outputs. The J and K data is accepted by the flip-flop on the rising edge of the clock pulse. The triggering occur...
Vendor:Other Category:Other
This DM54LS107A device contains two independent negative-edge-trig-gered J-K flip-flops with complementary outputs. The J and K data is processed by the flip-flops on the falling edge of the clock pulse. The clock trig...
Vendor:Other Category:Other
This DM54LS10 device contains three independent gates each of which performs the logic NAND function.
Vendor:Other Category:Other
This DM54LS08 device contains four independent gates each of which performs the logic AND function.
Vendor:Other Category:Other
This DM54LS04 device contains six independent gates each of which performs the logic INVERT function.
Vendor:Other Category:Other
This DM54LS03 device contains four independent gates each of which performs the logic NAND function. The open-collector outputs require external pull-up resistors for proper logical operation.
Vendor:Other Category:Other
This DM54LS02 device contains four independent gates each of which performs the logic NOR function.
Vendor:Other Category:Other
This DM54LS00 device contains four independent gates each of which performs the logic NAND function.
© 2008-2012 SeekIC.com Corp.All Rights Reserved.